Perle Systems IOLAN CSS Manuel d'utilisateur Page 140
- Page / 164
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Run-Time Statistics
134 IOLAN SDS/SCS/STS CLI Reference Guide, Version 3.6
Show Modbus Statistics
Show Routes
Run-Time Statistics
Delete Arp
Show Arp
Show Serial
Uptime
Description Shows the Modbus statistics.
User Level Admin
Syntax
show modbus statistics master-tcp line *|<number>
show modbus statistics master-udp line *|<number>
show modbus statistics slave-tcp line *|<number>
show modbus statistics slave-udp line *|<number>
Description Shows current information about IPv4 or IPv6 network routes.
User Level Admin
Syntax
show routes [ipv6]
Description Delete entries from the IOLAN's ARP cache. Takes effect immediately; not related to
configuration.
User Level Admin
Syntax
delete arp
Description Shows the current contents of the ARP cache.
User Level Admin
Syntax
show arp
Description Shows statistics on the serial port.
User Level Admin
Syntax
show serial [<line_number>]
Description Displays the elapsed time (in days, hours, minutes, and seconds) since the last
reboot/power cycle.
User Level Admin
Syntax
uptime
- SDS/SCS/STS 1
- Command Line Interface 1
- Reference Guide 1
- Table of Contents 3
- About This Book 15
- Intended Audience 15
- Contacting Technical Support 16
- Repair Procedure 17
- Feedback on this Manual 17
- Introduction Chapter 1 19
- Command Shortcuts 20
- Command Options 20
- Server Commands Chapter 2 21
- Set Port-Buffering 22
- Set Server 23
- Set SSL Server 26
- Set Service 27
- Show Console 28
- Show Custom-App 28
- Show Port-Buffering 28
- Hardware Commands 29
- SSH Server Commands 29
- Show SSH-Server 30
- SSL/TLS Commands 31
- Set SSL Server Cipher-suite 32
- Modbus Commands 33
- Show Modbus 34
- Authentication Commands 35
- Set Authentication LDAP 36
- Set Authentication Kerberos 36
- Set Authentication NIS 37
- Add RADIUS 37
- Delete RADIUS 37
- Set Authentication RADIUS 38
- Set Authentication TACACS+ 39
- Set Authentication SecurID 39
- TruePort Baud Commands 40
- Email Commands 41
- Clustering Commands 42
- Set Clustering Slave-IP 43
- Show Clustering Slave-IP 43
- Dynamic DNS Commands 44
- Server Commands 45 45
- PCI Commands 47
- Set PCI Wireless-WAN 48
- Show Wireless-WAN 48
- IPv6 Commands 49
- Add Custom-IPv6 50
- Set Custom-IPv6 51
- Delete Custom-IPv6 51
- IPv6 Router Advertisements 52
- User Commands Chapter 3 53
- Set Termtype 55
- Set User 55
- Set User Session 56
- Show Line Users 57
- Syslog Console 58
- Show Sessions 58
- Show Termtype 58
- Configuring Users 60
- Set Default User 61
- Show Default User 68
- Show User 68
- Line Commands Chapter 4 69
- Line Commands 71 73
- Line Commands 73
- Set Line Interface 74
- Set Line Service 75
- Line Commands 75 77
- Set Modem 78
- Show Line 78
- Line Service Commands 79
- Set SSH-Client 80
- Line Commands 79 81
- Name and Password values 81
- Auto Login is enabled 81
- Set PPP Dynamic-DNS 86
- Set SLIP 86
- Set Vmodem 88
- Line Commands 87 89
- NO CARRIER will be sent 89
- CONNECT 9600 90
- Set Vmodem-Phone 91
- Set SSL Line 91
- Set SSL Line Cipher-suite 93
- Set Modbus-Slave Line 94
- Set Modbus-Master Line 94
- Set Power-Management Line 95
- Set Multihost Line 96
- Set Line Initiate-Connection 96
- Show Interface 96
- Show Power-Management 96
- Modem Commands 98
- Packet Forwarding Commands 100
- Line Commands 99 101
- Transmit Timer 101
- Show Packet-Forwarding Line 103
- Network Commands Chapter 5 105
- Delete Trap 106
- Set SNMP 106
- Delete Community 106
- Set SNMP V3-Security 107
- TFTP Commands 108
- Hosts Commands 108
- DNS/WINS Commands 109
- Delete DNS 110
- Delete WINS 110
- Show DNS 110
- Show Server 110
- Show WINS 110
- Gateway Commands 111
- Delete Gateway 112
- Set Gateway 112
- Show Gateways 112
- Logging Commands 113
- RIP Commands 114
- Show RIP 115
- IPsec Commands 116
- IPv6 Tunnels 119
- Set IPv6tunnel 120
- Show IPv6tunnel 120
- Delete IPv6tunnel 120
- L2TP/IPsec 121
- Default Gateway value (if no 122
- VPN Exceptions 123
- Delete VPN Exception 124
- Show VPN Exception 124
- Time Commands Chapter 6 125
- SNTP Commands 126
- Time/Date Setting Commands 127
- Set Summertime Fixed 128
- Set Summertime Recurring 128
- Show Date 129
- Show Summertime 129
- Administration 131
- Commands Chapter 7 131
- TFTP File Transfer Commands 132
- Custom Factory Default 134
- MOTD Commands 137
- Statistics Commands Chapter 8 139
- Run-Time Statistics 140
- IOLAN+ User 141
- Commands Chapter 9 141
- I/O Commands Chapter 10 143
- Set Line 144
- Set IOChannel 145
- Set IOChannel Digital Input 146
- Set IOChannel Digital Output 148
- Set IOChannel Relay 150
- Set IOChannel IOExtension 154
- I/O Commands 149 155
- Set IOChannel Multihost 156
- Set IOChannel IOExtension SSL 157
- Show IOChannel Status 157
- Kill IOChannel 157
- I/O Channel Control Commands 158
- Digital Input 159
- Analog Input 159
- Calibrate Analog 159
- Reset Calibration 159
- Power Commands Chapter 11 161
- Power Commands 162
- Glossary 163
© 2020, manymanuals.fr. Tous droits réservés | 0.081 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels